Geeky Teens Room: DIY Wood Hexagon Coasters

DIY Wood Hexagon Coasters

Sometimes when my iPhone is covered in sawdust and my hand is cramping up and I accidentally sand off my beautiful stain and have to start over on a project, I wonder why I DIY.

And then I get to the end of a project and see this:

DIY Wood Hexagon Coasters || Jade and Fern

And I remember that it’s so awesome to make things.

You need coasters. You want to be filled with badass DIY pride. Clearly that means you need to make this project.

I’m not gonna lie—this is probably the most involved DIY I’ve posted to date. But it’s still easy and doable, so don’t shy away if you’re a newbie maker. Plus the bulk of the work involves hand-sawing, making it the perfect opportunity to tone the bicep of your dominant arm. And who doesn’t want one sexy arm?

And there’s a template! Templates mean easy! Let’s make hexagon coasters!

DIY Wood Hexagon Coasters

Skill Level: Easy, but involved

Time: 6 hours active, 2 days total

What You Need:

hexagon template (download below)
poplar hobby board (4′ long, 4″ wide, 1/2″ thick)
mini hacksaw with fine teeth and a thin blade
wood stain and/or white craft paint (the stain I used was Zar oil-based in Moorish Teak)
miscellaneous: scrap wood, lint-free rags (old cotton tees work well), pencil, ruler, scissors

Step One – Procure your wood and have it cut down into squares at a hardware store! Or if you have a power saw (if you do, may I steal it?), use that. Wood board widths are marked larger than they are—a 4″ board liked I used here is actually 3.5″ wide, so be sure to tell your helpful hardware store wood cutter that you want 3.5″ x 3.5″ squares.

Tip: Don’t worry about having too many squares, go ahead and have the whole board cut down, that way you’ll have extras if you mess up.

Step Two – Cut out the hexagon template and trace it onto the wood squares. You’ll only be cutting the corners—four cuts per square. Not too bad, right?

Step Three – Clamp the squares down to a work surface and saw off the corners following the template. You may think that you don’t need the clamp and can just hold down the coaster while sawing, but this will make your wrist hurt A LOT. Trust me.

I’ve included a (terrible) pic of the clamp so you can see how to use it. Stick a piece of scrap wood between the clamp and the coaster to protect it. The work surface doesn’t have to be fancy; I used a tiny rickety folding table in my driveway and it worked great!

Step Four – When all the coasters are cut out and your arm has turned to jelly, take a break. Then sand each coaster thoroughly, first with 120 grit sandpaper, then 200 grit. Wipe off all dust with a damp rag.

In case you’ve never worked with wood and aren’t convinced that sanding is necessary, take a look at the comparison between unsanded (left) and sanded (right). Look how soft and light and smooth the sanded coaster is! Sanding is necessary!

Step Five – Decorate!

I color-blocked some of my coasters with white craft paint and dark wood stain, but you can obviously decorate yours however you want. This post is already too long to explain how to stain wood, but there are excellent tutorials online—this video on This Old House should teach you the basics (watch through minute 2).

If you decide to stain only part of the coasters like I did, use a good quality painter’s tape pressed down REALLY REALLY well, and peel off the tape at a 45° angle as soon as you have the excess stain wiped off of the coaster (to prevent stain that is on top of the tape from bleeding through onto the wood). This is an advanced technique so don’t worry if it takes you a few tries!

Step Six – Seal the coasters with a clear polycrylic finish to protect them and give them a nice satiny sheen. I like to apply polycrylic with a cheapo foam brush, just be sure to follow the instructions on the can.

There are spray-on finishes you can use too, I’m just not sure which ones are good for stained wood as I haven’t used them myself, so if you want to go that route you’ll have to ask a hardware store.

Step Seven – Finally, use the hexagon template to cut out the adhesive cork and apply it to the back of the coasters. Cut the cork just a smidge smaller if you don’t want it to show from the top side.

And that’s (finally) it!

I’m a little in love with how the coasters came out. And I’m very excited to have more hexagons in my apartment (my honeycomb wall decal has to come down soon so we can paint the lavender living room).